Semi-Dirac and optical-pumping models #
The semi-Dirac records below extract the anisotropic low-energy dispersion and pump-response bookkeeping discussed by Ghosh, Bandyopadhyay, and Singh and by Uchoa et al. They are finite conditional models. They do not assert that a lignin-vitrimer, rGO, Proca resonator, graphene layer, or fiber laser realizes these equations, and they do not infer an absolute process power from the papers.
A two-dimensional semi-Dirac dispersion with a linear y direction and a quadratic x direction. The energy scale is normalized so the coefficients have already absorbed the relevant unit conversions.
- mass : ℝ
- mass_pos : 0 < self.mass
- linearVelocity : ℝ
- linearVelocity_pos : 0 < self.linearVelocity
- momentumX : ℝ
- momentumY : ℝ
- energy : ℝ
- energy_nonnegative : 0 ≤ self.energy
- dispersionLaw : self.energy ^ 2 = (self.momentumX ^ 2 / (2 * self.mass)) ^ 2 + (self.linearVelocity * self.momentumY) ^ 2
Instances For
The semi-Dirac energy shell is the supplied anisotropic dispersion law.
Along the quadratic axis, the model energy is quadratic in momentum when there is no momentum on the linear axis.
Along the linear axis, the model energy is linear in the absolute momentum at the level of squared energy.
A pump-dependent anisotropic response, stored as a conditional linear response law. The pump is a nonnegative optical power and the two response coefficients are measured or supplied model inputs.
- pumpPower : Units.Power
- quadraticResponse : ℝ
- quadraticResponse_nonnegative : 0 ≤ self.quadraticResponse
- linearResponse : ℝ
- linearResponse_nonnegative : 0 ≤ self.linearResponse
- quadraticResponseGain : ℝ
- quadraticResponseGain_nonnegative : 0 ≤ self.quadraticResponseGain
- linearResponseGain : ℝ
- linearResponseGain_nonnegative : 0 ≤ self.linearResponseGain
- quadraticSignal : ℝ
- quadraticSignal_nonnegative : 0 ≤ self.quadraticSignal
- linearSignal : ℝ
- linearSignal_nonnegative : 0 ≤ self.linearSignal
- quadraticResponseLaw : self.quadraticSignal = self.quadraticResponse + self.quadraticResponseGain * self.pumpPower.watts
- linearResponseLaw : self.linearSignal = self.linearResponse + self.linearResponseGain * self.pumpPower.watts
Instances For
Optical pumping changes the quadratic-axis response according to the supplied calibration law.
Optical pumping changes the linear-axis response according to the supplied calibration law.
A positive pump and strictly positive calibrated gain increase an axis response.
The corresponding monotonicity result for the linear axis.
Power allocated to an optical control chain. fiberLaserPower is the
laser electrical/optical input budget, while the remaining powers are declared
loads or losses.
- fiberLaserPower : Units.Power
- fiberLaserPower_nonnegative : 0 ≤ self.fiberLaserPower.watts
- resonatorPower : Units.Power
- resonatorPower_nonnegative : 0 ≤ self.resonatorPower.watts
- metamaterialPower : Units.Power
- metamaterialPower_nonnegative : 0 ≤ self.metamaterialPower.watts
- processPower : Units.Power
- processPower_nonnegative : 0 ≤ self.processPower.watts
- lossPower : Units.Power
- inputPower : Units.Power
- inputPower_nonnegative : 0 ≤ self.inputPower.watts
- powerBalance : self.resonatorPower.watts + self.metamaterialPower.watts + self.processPower.watts + self.lossPower.watts = self.inputPower.watts
- laserInputLaw : self.inputPower.watts = self.fiberLaserPower.watts
Instances For
The declared fiber-laser input supplies all listed control, process, and loss powers.
No declared process or control output can exceed the fiber-laser input.
A calibrated absorbed-power requirement gives a necessary lower bound on fiber-laser power after an explicit end-to-end efficiency.
- budget : SemiDiracOpticalPowerBudget
- endToEndEfficiency : Propagation.BoundedFactor
- absorbedPower : Units.Power
- absorbedPower_nonnegative : 0 ≤ self.absorbedPower.watts
- absorbedPowerLaw : self.absorbedPower.watts = self.endToEndEfficiency.value * self.budget.fiberLaserPower.watts
- requiredAbsorbedPower : Units.Power
- requiredAbsorbedPower_nonnegative : 0 ≤ self.requiredAbsorbedPower.watts
- thresholdLaw : self.requiredAbsorbedPower.watts ≤ self.absorbedPower.watts
- materialCalibrationSpecified : Bool
- phaseIdentificationSpecified : Bool
- grapheneFormationVerified : Bool
Instances For
The process threshold is met only when the declared absorbed power reaches its calibrated requirement.
Under a positive end-to-end efficiency, meeting the calibrated threshold requires at least threshold divided by efficiency at the fiber-laser input.